Interfacing PIC16F887 with FAT16 SD card
After reading raw data (bytes and sectors) from SD card, now I'm going to use FAT16 file system to read and print text file located in 2 GB SD card.Read SD card raw data topic:
MMC/SD Card raw data read with PIC16F887 microcontroller
UART protocol is used to display the content of the text file.
For this project, I used MMC/SD card driver for CCS C compiler which can be found in:
MMC/SD Card driver for CCS PIC C compiler
And I used FAT16 library (for reading files) for CCS C compiler which can be downloaded from:
FAT16 Library for CCS C compiler
Hardware Required:
- PIC16F887 microcontroller
- FAT16 formatted MMC/SD card ( <= 2 GB)
- ASM1117 3.3 voltage regulator
- 3 x 3.3K ohm resistor
- 3 x 2.2K ohm resistor
- 10K ohm resistor
- 5 x 10uF polarized capacitor
- 100nF ceramic capacitor
- MAX232 chip
- Female COM port
- 5V Power source
- Breadboard
- Jumper wires
I used just one wire (RD2) to transmit data from the microcontroller to the PC (there is no need for the MCU to receive data so the receiving wire is not connected).
The chip select pin of the SD card is connected to pin RD3 (the SD card chip select pin is active low).
In this project the PIC16F887 MCU uses its internal oscillator and MCLR pin function is disabled.
Read text files from FAT16 SD card with PIC16F887 C code:
The C code below was tested with CCS C compiler version 5.051.
SD card driver and FAT16 library for CCS must be added to the project, just by putting the two source codes in the project folder or the CCS driver folder.
In this example I used the hardware SPI module of the PIC16F887, software SPI also works but the hardware one is much faster.
I named the text file "mytext" (basically it is mytext.txt) but in the CCS C code we've to add the extension of the file which becomes "mytext.txt".
I used a read buffer of 10 bytes ( file_data[10] ), so the microcontroller reads the text file 10 bytes by 10 bytes, it reads 10 bytes and send it to the PC via RS232 then the second 10 bytes and so on until the function fat16_read_data(10, file_data) returns 1 which means we're at the end of the file.
The functions used in the C code are:
fat16_init(): initializes the SD card and the FAT16 file system, return 0 if OK and 1 if error.
fat16_open_file(txt): opens file with predefined name.
fat16_read_data(10, file_data): read data (10 bytes) from the opened file and save it in the array file_data.
printf: outputs data over RS232 where printf("%s", file_data); outputs a string of characters (file_data).
Complete C code is below.
/* Read and print text file from FAT16 microSD card using PIC16F887 MCU. Fat16 library and MMC/SD card driver for CCS C compiler must be installed http://ccspicc.blogspot.com/ electronnote@gmail.com */ // SD Card module connections #define SDCARD_SPI_HW // Hardware SPI module is used for the SD card #define SDCARD_PIN_SELECT PIN_D3 // SD card chip select pin is connected to pin RD3 // End SD card module connections #include <16F887.h> #fuses NOMCLR, INTRC_IO, NOBROWNOUT, NOLVP #use delay(clock = 8MHz) #use rs232(xmit = PIN_D2, rcv = PIN_D1, baud = 9600) #include <sdcard.c> // SD card diver source file #include <fat16.c> // FAT16 Library source file int8 file_data[10]; void open_file(){ const int8 *txt = "mytext.txt"; // File name 'mytext.txt' if(fat16_open_file(txt) == 0){ printf("OK!"); printf("\n\r"); // Start new line while(fat16_read_data(10, file_data) == 0) // Read file data printf("%s", file_data); // Print file data as string return; } printf("\n\r"); // Start new line printf("File opening error!"); } void main(){ setup_oscillator(OSC_8MHZ); // Set internal oscillator to 8MHz set_tris_d(0); // Configure PORTD pins as outputs delay_ms(2000); printf("\n\r"); // Start new line printf("*** Read text file from FAT16 SD card using PIC16F887 ***"); delay_ms(2000); printf("\n\r"); // Start new line printf("Initializing FAT16 library ...... "); if(fat16_init() == 0){ // If FAT16 file system and SD card were successfully initialized printf("OK!"); delay_ms(2000); printf("\n\r"); // Start new line printf("Opening file: 'mytext.txt'...... "); open_file(); } else { // Problem occured while the initialization printf("\n\r"); // Start new line printf("Initialization error!"); } printf("\n\r"); // Start new line printf("*** END ***"); while(TRUE) ; // Endless loop }After finishing the project, I got a result similar to the one shown in the video below where the used microcontroller is PIC16F877A.