DC motor interfacing with PIC18F4550 and L293D
This
topic shows how to control DC motor rotation direction and speed using
PIC18F4550 microcontroller and L293D motor driver chip.
A pot is used to control motor speed and two pushbuttons are used to control rotation direction.
Related topics:
The following topic shows how to control speed and direct of a DC motor using PIC18F4550 and H-bridge circuit:DC motor speed and direction control with PIC18F4550 microcontroller
DC motor control with PIC18F4550 and L293D circuit:
The nominal voltage of the motor is 12V as well as L293D VS input voltage. Always L293D VS voltage is the same as the DC motor voltage and L293D VSS voltage is +5V.
A pot (pin AN0) is used to change the motor speed.
The microcontroller PIC18F4550 reads analog data from channel 0 and use the digital value to set the PWM duty cycle. If direction 1 button is pressed the microcontroller starts PWM1 (RC2 pin) and stops PWM2 (RC1 pin) and if direction 2 button is pressed the microcontroller stops PWM1 (RC2 pin) and starts PWM2 (RC1 pin), when the stop button is pressed the microcontroller stops PWM1 and PWM2 signals and the motor will stop.
The PWM (PWM1 & 2) frequency is 488Hz.
DC motor control with PIC18F4550 and L293D CCS PIC C code:
PIC18F4550 Timer2 is configured to generate a PWM frequency of 488Hz and the microcontroller runs with 8MHz internal oscillator.
The microcontroller PIC18F4550 reads RA0 analog value and stores the digital value on variable (i), this variable is used to set duty cycle of the active PWM (PWM1 or PWM2).
// Dc motor control with PIC18F4550 and L293D CCS PIC C code
// http://ccspicc.blogspot.com/
// electronnote@gmail.com
#include <18F4550.h>
#device ADC = 10
#fuses NOMCLR INTRC_IO
#use delay(clock = 8000000)
#use fast_io(B)
#use fast_io(C)
unsigned int16 i ;
void main(){
setup_oscillator(OSC_8MHZ); // Set internal oscillator to 8MHz
output_b(0); // PORTB initial state
set_tris_b(7); // Configure RB0, RB1 & RB2 as inputs
output_c(0); // PORTC initial state
set_tris_c(0); // Configure PORTC pins as outputs
output_d(0); // PORTD initial state
set_tris_d(0); // Configure PORTD pins as outputs
setup_adc(ADC_CLOCK_DIV_8); // Set ADC conversion time to 8Tosc
setup_adc_ports(AN0); // Configure AN0 as analog input
set_adc_channel(0); // Select channel AN0
setup_timer_2(T2_DIV_BY_16, 255, 1); // Set PWM frequency to 500Hz
delay_ms(100); // Wait 100ms
while(TRUE){
i = read_adc(); // Read from AN0 and store in i
if(input(PIN_B3) == 1) // If direction 1 is selected
set_pwm1_duty(i); // Set pwm1 duty cycle
if(input(PIN_B4) == 1) // If direction 2 is selected
set_pwm2_duty(i); // Set pwm2 duty cycle
delay_ms(10); // Wait 10ms
if(input(PIN_B0) == 0){ // If RB0 button pressed
if(input(PIN_B3) == 0){ // If direction 1 not already selected
output_b(0); // Both LEDs OFF
setup_ccp1(CCP_OFF); // CCP1 OFF
setup_ccp2(CCP_OFF); // CCP2 OFF
output_c(0); // PORTC pins low
delay_ms(100); // Wait 100ms
setup_ccp1(CCP_PWM); // Configure CCP1 as a PWM
output_high(PIN_B3); // RB3 LED ON
}}
if(input(PIN_B1) == 0){ // If RB1 button pressed
if(input(PIN_B4) == 0){ // If direction 2 not already selected
output_b(0); // Both LEDs OFF
setup_ccp1(CCP_OFF); // CCP1 OFF
setup_ccp2(CCP_OFF); // CCP2 OFF
output_c(0); // PORTC pins low
delay_ms(100); // Wait 100ms
setup_ccp2(CCP_PWM); // Configure CCP2 as a PWM
output_high(PIN_B4); // RB4 LED ON
}}
if(input(PIN_B2) == 0){ // If RB2 button pressed
setup_ccp1(CCP_OFF); // CCP1 OFF
setup_ccp2(CCP_OFF); // CCP2 OFF
output_c(0); // PORTC pins low
output_b(0);} // Both LEDs OFF
}
}
DC motor control with PIC18F4550 and L293D Proteus simulation video:
The following video shows the simulation using Proteus.
Proteus simulation file download:
You can download Proteus simulation file from the following link.
DOWNLOAD
